SeaDoo Spark Forum banner

1 - 5 of 5 Posts

·
Registered
Joined
·
2 Posts
Discussion Starter #1
Hello everyone,

I recently purchased a 2015 sea doo spark and am very excited to use it this summer. I purchased it with only 7 hrs.

The other day I took it out for the first time and had a blast. Everything worked great as it should. I used the IBR function going pretty fast and heard a long beep. Then the IBR sign on the screen started blinking. The IBR bucket seemed to be stuck up. I shut the ski off and fired it back on. The bucket dropped down and neutral and reverse worked. Once I squeezed the throttle to go forward the same beep came on and IBR started blinking on the screen. Turned the ski off and back on and it did the exact same thing. The bucket stays down until I move forward with the throttle then then beeeeeep and IBR blinks.

I went through the wiring to make sure all connection were tight and it was receiving the correct voltage (it has a brand new battery in it) I also made sure fuses were tight and not blown. I proceeded to take the whole top half of the ski off to check to see if there were any wires shorting.... didn’t see anythjng

As a last effort I took the IBR bucket off to see if the arm was able to move back and forth freely without it.... NO DICE! Same problem was occurring.

I am still having the same issues. Does anyone have any advice? Should I take to a dealer? Is there an inexpensive code reader I can buy? Could I have fixed the problem and the computer just needs codes to be re set?

Any help would be much appreciated. Thank you for your time!!
 

·
Registered
Joined
·
233 Posts
Hello everyone,

I recently purchased a 2015 sea doo spark and am very excited to use it this summer. I purchased it with only 7 hrs.

The other day I took it out for the first time and had a blast. Everything worked great as it should. I used the IBR function going pretty fast and heard a long beep. Then the IBR sign on the screen started blinking. The IBR bucket seemed to be stuck up. I shut the ski off and fired it back on. The bucket dropped down and neutral and reverse worked. Once I squeezed the throttle to go forward the same beep came on and IBR started blinking on the screen. Turned the ski off and back on and it did the exact same thing. The bucket stays down until I move forward with the throttle then then beeeeeep and IBR blinks.

I went through the wiring to make sure all connection were tight and it was receiving the correct voltage (it has a brand new battery in it) I also made sure fuses were tight and not blown. I proceeded to take the whole top half of the ski off to check to see if there were any wires shorting.... didn’t see anythjng

As a last effort I took the IBR bucket off to see if the arm was able to move back and forth freely without it.... NO DICE! Same problem was occurring.

I am still having the same issues. Does anyone have any advice? Should I take to a dealer? Is there an inexpensive code reader I can buy? Could I have fixed the problem and the computer just needs codes to be re set?

Any help would be much appreciated. Thank you for your time!!
I have read about the module with the electronics basically getting corroded and the motors being fine, but it doesn't seem they sell things separately. Other than the few things I read like that I don't have any experience with it. If it happened to I might look into disabling it and removing it to ride until I figured out how to fix it.
 

·
Registered
Joined
·
2 Posts
Hello everyone,

I recently purchased a 2015 sea doo spark and am very excited to use it this summer. I purchased it with only 7 hrs.

The other day I took it out for the first time and had a blast. Everything worked great as it should. I used the IBR function going pretty fast and heard a long beep. Then the IBR sign on the screen started blinking. The IBR bucket seemed to be stuck up. I shut the ski off and fired it back on. The bucket dropped down and neutral and reverse worked. Once I squeezed the throttle to go forward the same beep came on and IBR started blinking on the screen. Turned the ski off and back on and it did the exact same thing. The bucket stays down until I move forward with the throttle then then beeeeeep and IBR blinks.

I went through the wiring to make sure all connection were tight and it was receiving the correct voltage (it has a brand new battery in it) I also made sure fuses were tight and not blown. I proceeded to take the whole top half of the ski off to check to see if there were any wires shorting.... didn’t see anythjng

As a last effort I took the IBR bucket off to see if the arm was able to move back and forth freely without it.... NO DICE! Same problem was occurring.

I am still having the same issues. Does anyone have any advice? Should I take to a dealer? Is there an inexpensive code reader I can buy? Could I have fixed the problem and the computer just needs codes to be re set?

Any help would be much appreciated. Thank you for your time!!
Hey did you ever find a solution to this problem? I have the exact same problem. Would appreciate knowing if you found a fix!!
Email is [email protected]
Thankyou!
 
1 - 5 of 5 Posts
Top